Análisis del comportamiento tribológico de casquetes microtexturizados para motores de combustión interna
| dc.contributor.advisor | Rudas, Sebastián | |
| dc.contributor.advisor | Gonzáles, Juan Manuel Gonzáles | |
| dc.contributor.author | Mejía Sánchez, Víctor Manuel | |
| dc.date.accessioned | 2026-11-20T14:45:27Z | |
| dc.date.available | 2026-11-20T14:45:27Z | |
| dc.date.issued | 2026 | |
| dc.description.abstract | Esta investigación analizó el comportamiento tribológico de casquetes de biela microtexturizados para motores de combustión interna, texturizados mediante mecanizado CNC y texturización láser. Se diseñaron cavidades circulares con diámetros nominales de 800, 1000 y 1200 𝜇𝑚, profundidad nominal de 100 𝜇𝑚 y tres distribuciones axiales, manteniendo constante la disposición circunferencial. Las microtexturas se caracterizaron dimensionalmente y se evaluaron en un bancomotor diésel KAMA accionado externamente, bajo condiciones controladas de 1800 rpm y temperatura de aceite cercana a 80 °C. Se registraron mediciones de torque, presión en recámara y temperatura; adicionalmente, se realizó un análisis factorial, gravimetría y evaluación post mortem mediante inspección macrográfica, microscopía electrónica de barrido y análisis EDS. El mecanizado CNC presentó mayor fidelidad geométrica global respecto al diseño nominal. El desempeño tribológico dependió principalmente del diámetro de las cavidades y de su interacción con la distribución axial. La configuración CNC 6×10, con diámetro de 800 𝜇𝑚, alcanzó la mayor reducción de torque, equivalente a 12,7 % respecto al casquete liso. La condición CNC 6×1, con diámetro de 1000 𝜇𝑚, presentó el mejor equilibrio entre reducción de torque y baja pérdida aparente de masa. La magnitud registrada experimentalmente fue el torque requerido para accionar externamente el conjunto entre la biela y el cigüeñal, el cual integra las pérdidas por fricción del sistema mecánico y no constituye una medida directa del coeficiente de fricción del par casquete y muñón; el indicador energético derivado corresponde a una presión media efectiva resistente equivalente, (MEPres), obtenida como transformación del torque promedio, y no a una presión media efectiva de fricción estricta. Los resultados evidencian que la microtexturización puede reducir la resistencia al giro, aunque su efectividad depende de la geometría real, el proceso de fabricación y la dinámica de lubricación. El aporte de la investigación consiste en establecer y verificar experimentalmente una metodología que articula, sobre casquetes comerciales y en un conjunto biela y cigüeñal representativo de un motor alternativo, el diseño geométrico paramétrico de la microtextura, su fabricación mediante dos tecnologías sustractivas de naturaleza distinta, la caracterización de la geometría real obtenida, la respuesta energética del sistema y la evidencia gravimétrica y morfológica posterior al ensayo. Estos resultados se establecen bajo la condición de una única observación experimental independiente por tratamiento factorial, por lo cual constituyen evidencia comparativa de carácter exploratorio para las configuraciones geométricas y las condiciones operativas evaluadas. | spa |
| dc.description.abstract | Abstract This study investigated the tribological behavior of microtextured connecting-rod bearing shells for internal combustion engines, manufactured by CNC machining and laser surface texturing. Circular dimples with nominal diameters of 800, 1000, and 1200 𝜇m, a nominal depth of 100 𝜇m, and three axial distributions were designed while maintaining a constant circumferential arrangement. The microtextures were dimensionally characterized and evaluated using an externally driven KAMA diesel engine test bench under controlled operating conditions of 1800 rpm and an oil temperature close to 80 °C. Torque, cylinder pressure, and oil temperature were recorded. In addition, factorial analysis, gravimetric measurements, and post-mortem assessment through macroscopic inspection, scanning electron microscopy, and energy-dispersive X-ray spectroscopy were conducted. CNC machining showed higher overall geometric fidelity to the nominal design. Tribological performance depended primarily on dimple diameter and its interaction with axial distribution. The CNC 6×10configuration with an 800 𝜇mdiameter achieved the largest torque reduction, 12.7% relative to the smooth bearing shell. The CNC 6×1configuration with a 1000 𝜇mdiameter provided the best balance between torque reduction and low apparent mass loss. The quantity recorded was the torque required to externally drive the connecting-rod and crankshaft assembly, which integrates the friction losses of the mechanical system and is not a direct measure of the friction coefficient of the shell–journal pair; the derived energy indicator is an equivalent resistive mean effective pressure, MEPres, obtained as a transformation of the average torque, and not a strict friction mean effective pressure. The findings show that microtexturing can reduce rotational resistance, although its effectiveness depends on the actual texture geometry, manufacturing process, and lubrication dynamics. The contribution of this work lies in establishing and experimentally verifying a methodology that links, on commercial bearing shells and in a connecting-rod and crankshaft assembly representative of a reciprocating engine, the parametric geometric design of the microtexture, its manufacture by two subtractive technologies of different nature, the characterisation of the actual geometry obtained, the energy response of the system, and the post-test gravimetric and morphological evidence. These results were obtained with a single independent experimental observation per factorial treatment and therefore constitute exploratory comparative evidence for the geometric configurations and operating conditions evaluated. | eng |
| dc.format.mimetype | application/pdf | |
| dc.identifier.uri | https://repositorio.pascualbravo.edu.co/handle/pascualbravo/3412 | |
| dc.language.iso | spa | |
| dc.publisher | Institución Universitaria Pascual Bravo | spa |
| dc.publisher.faculty | Facultad de ingeniería | |
| dc.publisher.place | Medellín, Colombia | |
| dc.publisher.program | Maestría en Energía | |
| dc.rights.accessrights | info:eu-repo/semantics/openAccess | |
| dc.rights.creativecommons | Atribución-NoComercial-SinDerivadas 4.0 Internacional (CC BY-NC-ND 4.0) | |
| dc.rights.uri | https://creativecommons.org/licenses/by-nc-nd/4.0/ | |
| dc.subject.lemb | Tribología | |
| dc.subject.lemb | Cojinetes | |
| dc.subject.lemb | Motores de combustión interna | |
| dc.subject.lemb | Motores diésel | |
| dc.subject.lemb | Fricción | |
| dc.subject.lemb | Superficies (Tecnología) | |
| dc.subject.lemb | Máquinas herramientas - Control numérico | |
| dc.subject.lemb | Láseres en la industria | |
| dc.thesis.grantor | Institución Universitaria Pascual Bravo | spa |
| dc.thesis.level | Maestría | |
| dc.thesis.name | Magíster en Energía | spa |
| dc.title | Análisis del comportamiento tribológico de casquetes microtexturizados para motores de combustión interna | spa |
| dc.type.coar | http://purl.org/coar/resource_type/c_bdcc | |
| dc.type.coarversion | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |
| dc.type.local | Tesis/Trabajo de grado - Monografía - Maestría | |
| dc.type.redcol | https://purl.org/redcol/resource_type/TM | |
| dc.type.version | info:eu-repo/semantics/publishedVersion | |
| oaire.accessrights | http://purl.org/coar/access_right/c_abf2 |
Files
License bundle
1 - 1 of 1
No Thumbnail Available
- Name:
- license.txt
- Size:
- 1.71 KB
- Format:
- Item-specific license agreed upon to submission
- Description:
